Pragna Agency
Mahadev Nagar Bhagwati Nagar, Surat, Gujarat
GST No. 24AFZPP2804F1Z9
TrustSEAL Verified
Call 0804898420294% Response Rate
SEND EMAIL
Product Details:
| Motor Horsepower | 5 to 20 HP |
| Motor Phase | Three Phase |
| Power Source | Electric |
| Brand | CRI |
| Maximum Head | 15 to 50 m |
| Warranty | 12 months |
| Motor Speed (RPM) | 2900 RPM |
| Usage/Application | Domestic, Agriculture, Industrial |
C.R.I. Openwell Submersible pumpsets are ideally suitable for open wells or tanks where a wide fluctuation of water level occur. This work under water and rest at the bottom of the well. Prime mover is rewindable, water-cooled motor
Motor sealing is made by polymers, ‘O’ rings, Oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel.
APPLICATIONSAdditional Information:
Product Details:
| Motor Horsepower | 1 - 3 HP |
| Type | Horizontal |
| Brand | CRI |
| Motor Phase | Three Phase |
| Motor Speed (RPM) | 2900 RPM |
| Impeller | Cast Iron / SS 410 / Bronze |
| Motor Shaft | SS 410 |
| Power Range | Vertical 2.2kW, 3.7kW, 3 HP, 50 HP |
| Maximum total head | 341 Meter |
| Maximum flow rate | 54 LPS |
| Bracket | Cast Iron |
| Power Range | Vertical 2.2kW - 37kW (3 HP - 7HP) |
| Voltage Range | Three-phase, 380 - 415V 50Hz, AC Supply |
| Maximum total head | 341 metre |
| Maximum flow rate | 54 lps (194 m³/hr) |
Additional Information:
Product Details:
| Motor Horsepower | 1 - 3 HP |
| Motor Phase | Three Phase |
| Power Source | Electric |
| Brand | CRI |
| Motor Speed (RPM) | 2900 RPM |
| Coupling | S.S 304 / S.S 410 |
| Viscosity | 1.75 x 10^6 Angstrom m^2/sec (max.) |
| Diffuser Chamber | Noryl |
| Maximum Total Head | Upto 108 Metre |
| Direction of Rotation | Counterclockwise from driving End(Vertical OWS),Clockwise from driving end( Horizontal OWS) |
| Specific Gravity | 1.004 (max.) |
| Nominal Outlet Size | 25,32,40,50 & 65 mm |
| Maximum Liquid Temperature | 33 Angstrom Degree Celsius (max.) |
| Turbidity | 50-ppm silica scale (max.) |
| Outer Shell | Mild Steel/ S.S |
| Hardness | 300 ppm (max.) |
| Shaft | SS- 410 |
| Power Range | 0.7 to 3 HP(.37kW-2.2kW) |
| Degree of Protection | IP 58 |
| Maximum Flow Rate | 10 lps(36 m^3(angstrom)/hr) |
| Casing | Cast Iron / S.S 304 / (DIN 1.4509) |
| Impeller | Cast Iron / Noryl / Delrin / S.S 304 |
| Method of starting | CSCR |
| Intermediate Angstrom Bearing Angstrom | S.S 304 / NBR |
| Type of Duty | S1(Continous) |
| Thrust Assembly | Leaded Bronze & Compostos / S.S 420 Vs Graphite Carbon |
| Allowable Solid | 3000 ppm (max.) |
| Journal Bearings | LTB4 |
| Locking Strip | Mild Steel / S.S |
| Versions | Single Angstrom phase 200-240V,50Hz,AC supply. CSCR,Three-phase 380-450 V,50V,AC supply. |
| Stop Angstrom Ring | S.S 304 / Hylem |
| Check Valve Seat | Nitrile Butyl Rubber |
| Check Valve | Delrin |
| Sand Guard Rubber | Nitrile Rubber |
| Chlorine Ion Density | 500 ppm (max.) |
| Usage/Application | Domestic |
| Permissiable Amount of Sand | 50 gm/m(Angstrom)^3 (max.) |
Additional Information:
Product Details:
| Number Of Stages | Multi Stage Pump |
| Motor Horsepower | 1 - 3 HP |
| Motor Phase | Single Phase |
| Brand | CRI |
| Maximum Discharge Flow | 100 - 500 LPM |
| Warranty | 12 months |
| Discharge Outlet Size | 25 to 50 mm |
| Motor Speed (RPM) | 2900 |
| Type | Water Filled, Electric |
| Material of Construction | SS |
| Capacity (lpm) | 210 LPM |
| Color | Green |
| Coupling | Yes |
| Frequency (Hertz) | 50 Hz |
| Head (Meter) | 9-55 |
| Pressure (Meter Cube Per Hour) | 12.6 |
| Pump Size (Millimeter) | 32 |
| Voltage (Volt) | 220-240 |
| Weight (Kilogram) | 15 |
| Shaft Material | SS |
| Minimum Cooling Flow | 1.8m3/hr |
| Flow Rating | 1.8m3/hr |
| Max Flow Rate | 12.6m3/hr |
| Maximum Operating Pressure (in Bar) | 4.5 |
| Motor Voltage | 220-240 |
| Model | CSS-4S |
| Diameter | 32 mm |
| Power Consumption (in kw) | 1.5 |
| Capacity | 2 hp |
C.R.I. Openwell Submersible pumpsets are ideally suitable for open wells or tanks where a wide fluctuation of water level occur. This work under water and rest at the bottom of the well. Prime mover is rewindable, water-cooled motor
Motor sealing is made by polymers, ‘O’ rings, Oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel.
APPLICATIONSAdditional Information:
Product Details:
| Number Of Stages | Single-stage Pump |
| Brand | CRI |
| Usage/Application | Remove Water From Canal |
| Motor Phase | Single Phase |
| Head | 15 to 50 m |
| Motor Speed (RPM) | 2900 |
| Model Number | CSS-24(HH) |
C.R.I. Openwell Submersible pumpsets are ideally suitable for open wells or tanks where a wide fluctuation of water level occur. This work under water and rest at the bottom of the well. Prime mover is rewindable, water-cooled motor
Additional Information:
Product Details:
| Number Of Stages | Single-stage Pump |
| Head | Less than 15 m |
| Motor Horsepower | 1 to 3 HP |
| Motor Phase | Single Phase |
| Power Source | Electric |
| Brand | CRI |
| Warranty | 12 months |
| Maximum Discharge Flow | 100 - 500 LPM |
| Material of Construction | SS 304 |
| Discharge Outlet Size | 25 to 50 mm |
| Motor Speed (RPM) | 2900 RPM |
| Usage/Application | Domestic, Agriculture |
Additional Information:
Product Details:
| Power | 0.5 hp |
| Usage/Application | Industrial, Domestic |
| Motor Phase | Single Phase |
| Power Source | Electric |
| Brand | CRI |
| Warranty | 12 months |
| Fluid Temperature Range | 33 Degree C |
| Material of Construction | SS 304 |
| Discharge Outlet Size | 25 mm |
| Motor Speed (RPM) | 2900 RPM |
| Head | 15 m |
Additional Information:
Product Details:
| Motor Phase | Single Phase |
| Maximum Head | 15 to 50 m |
| Warranty | 12 months |
| Maximum Discharge Flow | 100 - 500 LPM |
| Minimum Flow | 1800PH |
| Size | 25mm |
| Minimum Head | 22.5 m |
| Maximum Flow | 10800LPH |
Additional Information:
Product Details:
| Number Of Stages | Single-stage Pump |
| Brand | CRI |
| Usage/Application | Filling Tank |
| Type | Horizontal |
| Motor Phase | Single Phase |
| Head | Less than 15 m |
| Power Rating | 3 Phase |
| Diaphragm | Nitryl Rubber |
| Max Flow Rate | 9 m3/hr |
| Motor Horsepower | Less than 1 HP |
C.R.I. Openwell Submersible pumpsets are ideally suitable for open wells or tanks where a wide fluctuation of water level occur. This work under water and rest at the bottom of the well. Prime mover is rewindable, water-cooled motor
Motor sealing is made by polymers, ‘O’ rings, Oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel.
APPLICATIONS
Product Details:
| Motor Horsepower | 1 - 3 HP |
| Motor Phase | Single Phase |
| Type | Horizontal |
| Model | Plano-100 |
| Size | 25 mm |
| Speed | 2900RPM |
C.R.I. Horizontal Openwell Submersible Pumpsets are ideally suitable for Openwell / Tanks where a wide fluctuation of water level occur.
This works under water and rest at the bottom of the well or tank. Hence suction and priming problem will not arise. The optimal design of impeller and diffusers enables the best possible hydraulic efficiency.
APPLICATIONSAdditional Information:
Product Details:
| Minimum Order Quantity | 10 Piece |
| Head | 31 M |
| Max Flow Rate | 18000 LPH |
| Journal Bearings | LTB4 |
| Locking Strip | Mild Steel / S.S |
| Outer Shell | Mild Steel/ S.S |
| Shaft | SS- 410 |
| Stop Angstrom Ring | S.S 304 / Hylem |
| Chlorine Ion Density | 500 ppm (max.) |
| Hardness | 300 ppm (max.) |
| Allowable Solid | 3000 ppm (max.) |
| Turbidity | 50-ppm silica scale (max.) |
| Pump Shaft | S.S 304 / S.S 410 |
| Versions | Single Angstrom phase 200-240V,50Hz,AC supply. CSCR,Three-phase 380-450 V,50V,AC supply. |
| Check Valve Seat | Nitrile butyl rubber |
| Shaft Seal | Nitrile butyl Rubber |
| Sand Guard Rubber | Nitrile Rubber |
| Maximum Liquid Temperature | 33 Angstrom Degree Celsius (max.) |
| Diaphragm | High Nitrile Rubber |
| Viscosity | 1.75 x 10^6 Angstrom m^2/sec (max.) |
| Diffuser Chamber | Noryl |
| Casing | Cast Iron / S.S 304 / (DIN 1.4509) |
| Speed | 2880 RPM |
| Power Range | 0.7 to 3 HP(.37kW-2.2kW) |
| Intermediate Angstrom Bearing Angstrom | S.S 304 / NBR |
| Degree of Protection | IP 58 |
| Model | css-16 |
| Impeller | Cast Iron / Noryl / Delrin / S.S 304 |
| Power | 3 phhase |
| Maximum Flow Rate | 10 lps(36 m^3(angstrom)/hr) |
| Direction of Rotation | Counterclockwise from driving End(Vertical OWS),Clockwise from driving end( Horizontal OWS) |
| Suction Inter Connector | Cast Iron |
| Maximum Total Head | Upto 108 Metre |
| Coupling | S.S 304 / S.S 410 |
| Check Valve | Delrin |
| Method of starting | CSCR |
| Upper Housing | Cast Iron |
| Thrust Assembly | Leaded Bronze & Compostos / S.S 420 Vs Graphite Carbon |
| Check Angstrom Valve Angstrom Housing | Cast Iron |
| Nominal Outlet Size | 25,32,40,50 & 65 mm |
| Permissiable Amount of Sand | 50 gm/m(Angstrom)^3 (max.) |
| Type of Duty | S1(Continous) |
| Specific Gravity | 1.004 (max.) |
Additional Information:
Product Details:
| Power Source | 1 phase |
| Head | 33 mtr |
| Max Flow Rate | 10800lph |
| Model | CSS-24 |
| pH Value | 6.5 to 8.5 |
| Valve Seat | Nitrile butyl rubber |
| Journal Bearings | LTB4 |
| Pump Shaft | S.S 304 / S.S 410 |
| Nominal Outlet Size | 25,32,40,50 & 65 mm |
| Suction inter Connector | Cast Iron |
| Coupling | S.S 304 / S.S 410 |
| Shaft | SS- 410 |
| Locking Strip | Mild Steel / S.S |
| Diffuser Chamber | Noryl |
| Chlorine Ion Density | 500 ppm (max.) |
| Hardness | 300 ppm (max.) |
| Maximum Total Head | Upto 108 Metre |
| Stop Angstrom Ring | S.S 304 / Hylem |
| Power Range | 0.7 to 3 HP(.37kW-2.2kW) |
| Degree of Protection | IP 58 |
| Outer Shell | Mild Steel/ S.S |
| Maximum Flow Rate | 10 lps(36 m^3(angstrom)/hr) |
| Maximum Liquid Temperature | 33 Angstrom degree C (max.) |
| Type of Duty | S1(Continous) |
| Method of starting | CSCR |
| Valve | Delrin |
| Casing | Cast Iron / S.S 304 / (DIN 1.4509) |
| Viscosity | 1.75 x 106 Angstrom m2/sec (max.) |
| Direction of Rotation | Counterclockwise from driving End(Vertical OWS),Clockwise from driving end( Horizontal OWS) |
| Thurst Assembly | Leaded Bronze & Compostos / S.S 420 Vs Graphite Carbon |
| Sand Guard Rubber | Nitrile Rubber |
| Impeller | Cast Iron / Noryl / Delrin / S.S 304 |
| Intermediate Angstrom Bearing Angstrom | S.S 304 / NBR |
| Specific Gravity | 1.004 (max.) |
| Diaphragm | High Nitrile Rubber |
| Turbidity | 50-ppm silica scale (max.) |
| Allowable Solid | 3000 ppm (max.) |
| Versions | Single Angstrom phase 200-240V,50Hz,AC supply. CSCR,Three-phase 380-450 V,50V,AC supply. |
| Speed | 2880 RPM |
Additional Information:
Product Details:
| Head | 15 to 50 m |
| Maximum Discharge Flow | 501-1000 LPM |
| Discharge Outlet Size | 1 to 2 in |
| Brand | CRI |
| Motor Horsepower | 0.5 HP |
| Motor Phase | Single Phase |
C.R.I. Openwell Submersible pumpsets are ideally suitable for open wells or tanks where a wide fluctuation of water level occur. This work under water and rest at the bottom of the well. Prime mover is rewindable, water-cooled motor
Additional Information:
Product Details:
| Power | 3 hp |
| Motor Phase | Single Phase |
| Brand | CRI |
| Warranty | 12 months |
| Material of Construction | Cast Iron |
| Type | Horizontal |
| Motor Speed (RPM) | 2900 RPM |
| Minimum Head | 20.5 mtr |
| Minimum FLow | 1800 LPH |
| Maximum Flow | 18000 LPH |
Additional Information:
Product Details:
| Usage/Application | Domestic, Industrial, Agriculture |
| Motor Phase | Three Phase |
| Power Source | Electric |
| Brand | CRI |
| Maximum Head | 15 to 50 m |
| Warranty | 12 months |
| Maximum Discharge Flow | 100 - 500 LPM |
| Fluid Temperature Range | 33 |
| Discharge Outlet Size | 25 to 50 mm |
| Material of Construction | CI |
| Motor Speed (RPM) | 2900 |
| Coupling | S.S 304 / S.S 410 |
| Maximum Flow Rate | 10 lps(36 m^3(angstrom)/hr) |
| Turbidity | 50-ppm silica scale (max.) |
| Impeller | Cast Iron / Noryl / Delrin / S.S 304 |
| Locking Strip | Mild Steel / S.S |
| Check Valve Seat | Nitrile butyl rubber |
| Chlorine Ion Density | 500 ppm (max.) |
| pH Value | 6.5 to 8.5 |
| Hardness | 300 ppm (max.) |
| Shaft | SS- 410 |
| Diffuser Chamber | Noryl |
| Diaphragm | High Nitrile Rubber |
| Check Valve | Delrin |
| Casing | Cast Iron / S.S 304 / (DIN 1.4509) |
| Maximum Liquid Temperature | 33 Angstrom Degree Celsius (max.) |
| Permissiable Amount of Sand | 50 gm/m(Angstrom)^3 (max.) |
| Direction of Rotation | Counterclockwise from driving End(Vertical OWS),Clockwise from driving end( Horizontal OWS) |
| Maximum Total Head | Upto 108 Metre |
| Journal Bearings | LTB4 |
| Sand Guard Rubber | Nitrile Rubber |
| Suction Inter Connector | Cast Iron |
| Versions | Single Angstrom phase 200-240V,50Hz,AC supply. CSCR,Three-phase 380-450 V,50V,AC supply. |
| Specific Gravity | 1.004 (max.) |
| Power Range | 0.7 to 3 HP(.37kW-2.2kW) |
| Upper Housing | Cast Iron |
| Pump Shaft | S.S 304 / S.S 410 |
| Nominal Outlet Size | 25,32,40,50 & 65 mm |
| Allowable Solid | 3000 ppm (max.) |
| Degree of Protection | IP 58 |
| Intermediate Angstrom Bearing Angstrom | S.S 304 / NBR |
| Viscosity | 1.75 x 10^6 Angstrom m^2/sec (max.) |
| Stop Angstrom Ring | S.S 304 / Hylem |
| Type of Duty | S1(Continous) |
| Outer Shell | Mild Steel/ S.S |
| Method of starting | CSCR |
| Thrust Assembly | Leaded Bronze & Compostos / S.S 420 Vs Graphite Carbon |
| Speed | 2880 RPM |
C.R.I. Openwell Submersible pumpsets are ideally suitable for open wells or tanks where a wide fluctuation of water level occur. This work under water and rest at the bottom of the well. Prime mover is rewindable, water-cooled motor
Motor sealing is made by polymers, ‘O’ rings, Oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel.
APPLICATIONSAdditional Information:
Product Details:
| Type | Horizontal |
| Chlorine Ion Density | 500 ppm (max.) |
| Journal Bearing | LTB 4 |
| Hardness | 300 ppm (max.) |
| Allowable Solid | 3000 ppm (max.) |
| Turbidity | 50-ppm silica scale (max.) |
| Versions | Three-phase,380-415V,50Hz,AC supply |
| Shaft Seal | Nitrile butyl rubber |
| Maximum Liquid Temperature | 33 Angstrom degree C (max.) |
| Diaphragm | High Nitrile butyl rubber |
| Viscosity | 1.75 x 10^6 Angstrom m^2/sec (max.) |
| Permissible amount of sand | 25 gm/m(Angstrom)^3 (max.) |
| Rear Cover | Cast Iron |
| Nominal Delivery Size | 50,65,80 & 100 mm |
| Impeller | Cast iron / SS 410 / LTB-2 |
| pH Value | 6.5 to 8.5 |
| Direction of Rotation | Counter Clockwise from driving end |
| Stator Shell | Cast iron / S.S / M.S |
| Degree of Protection | IP 58 |
| Pump Casing | Cast iron |
| Type of Duty | S1(continous) |
| Method of Starting | Direct on line upto 5.5kW,SD upto 37kW |
| Specific Gravity | 1.004 (max.) |
| Thurst Assembly | Leaded Bronze & Compostos / SS 420 with Graphite Carbon |
| Power Range | 2.2kW-15kW(0.5-20HP)Horizontal,2.2kW-37kW(1.0-50HP) Vertical |
| Shaft | SS AISI 410 / EN-8 |
| Maximum Start per Hour | 10 times |
| Maximum Flow Rate | Upto 195 m^3(Angstrom)/hr(54lps) |
| Maximum Total Head | Upto 341 metre |
| Speed | 2900 RPM |
Additional Information:
Product Details:
| Brand | CRI |
| Motor Horsepower | 1 - 3 HP |
| Motor Phase | Three Phase |
| Type | Horizontal |
| Power Source | 3 phase |
| Pump Shaft | S.S 304 / S.S 410 |
| Casing | Cast Iron / S.S 304 / (DIN 1.4509) |
| Shaft | SS- 410 |
| Degree Of Protection | IP 58 |
| Direction Of Rotation | Counterclockwise from driving End(Vertical OWS),Clockwise from driving end( Horizontal OWS) |
| Maximum Total Head | Upto 108 Metre |
| Specific Gravity | 1.004 (max.) |
| Nominal Outlet Size | 25,32,40,50 & 65 mm |
| Outer Shell | Mild Steel/ S.S |
| Diaphragm | High Nitrile Rubber |
| Check Angstrom Valve Angstrom Housing | Cast Iron |
| Turbidity | 50-ppm silica scale (max.) |
| Hardness | 300 ppm (max.) |
| Permissiable Amount of Sand | 50 gm/m(Angstrom)^3 (max.) |
| Speed | 2880 RPM |
| Check Valve Seat | Nitrile butyl rubber |
| Diffuser Chamber | Noryl |
| Type of Duty | S1(Continous) |
| Power Range | 0.7 to 3 HP(.37kW-2.2kW) |
| Stop Angstrom Ring | S.S 304 / Hylem |
| Maximum Liquid Temperature | 33 Angstrom Degree Celsius (max.) |
| Allowable Solid | 3000 ppm (max.) |
| Sand Guard Rubber | Nitrile Rubber |
| pH Value | 6.5 to 8.5 |
| Method of starting | CSCR |
| Upper Housing | Cast Iron |
| Locking Strip | Mild Steel / S.S |
| Impeller | Cast Iron / Noryl / Delrin / S.S 304 |
| Suction Inter Connector | Cast Iron |
| Thrust Assembly | Leaded Bronze & Compostos / S.S 420 Vs Graphite Carbon |
| Versions | Single Angstrom phase 200-240V,50Hz,AC supply. CSCR,Three-phase 380-450 V,50V,AC supply. |
| Intermediate Angstrom Bearing Angstrom | S.S 304 / NBR |
| Chlorine Ion Density | 500 ppm (max.) |
| Check Valve | Delrin |
| Journal Bearings | LTB4 |
| Shaft Seal | Nitrile butyl Rubber |
| Maximum Flow Rate | 10 lps(36 m^3(angstrom)/hr) |
| Viscosity | 1.75 x 10^6 Angstrom m^2/sec (max.) |
Additional Information:
Product Details:
| Number Of Stages | Single-stage Pump |
| Brand | Plano |
| Head (Water Lifting Capacity) | 15 to 50 m |
| Voltage | 215 V |
| Discharge Outlet Size (mm) | 1 to 2 in |
Specification:-
Additional Information:
Product Details:
| Diaphragm | High Nitrile Rubber |
| Direction of Rotation | Counterclockwise from driving End(Vertical OWS),Clockwise from driving end( Horizontal OWS) |
| Shaft | SS- 410 |
| Stop Angstrom Ring | S.S 304 / Hylem |
| Turbidity | 50-ppm silica scale (max.) |
| Type of Duty | S1(Continous) |
| Locking Strip | Mild Steel / S.S |
| Thurst Assembly | Leaded Bronze & Compostos / S.S 420 Vs Graphite Carbon |
| Valve Seat | Nitrile butyl rubber |
| Allowable Solid | 3000 ppm (max.) |
| Suction inter Connector | Cast Iron |
| Maximum Flow Rate | 10 lps(36 m^3(angstrom)/hr) |
| Maximum Total Head | Upto 108 Metre |
| Nominal Outlet Size | 25,32,40,50 & 65 mm |
| Sand Guard Rubber | Nitrile Rubber |
| Upper Housing | Cast Iron |
| Hardness | 300 ppm (max.) |
| Intermediate Angstrom Bearing Angstrom | S.S 304 / NBR |
| Journal Bearings | LTB4 |
| Maximum Liquid Temperature | 33 Angstrom degree C (max.) |
| Viscosity | 1.75 x 106 Angstrom m2/sec (max.) |
| pH value | 6.5 to 8.5 |
| Speed | 2880 RPM |
| Valve | Delrin |
| Chlorine Ion Density | 500 ppm (max.) |
| Diffuser Chamber | Noryl |
| Impeller | Cast Iron / Noryl / Delrin / S.S 304 |
| Power Range | 0.7 to 3 HP(.37kW-2.2kW) |
| Pump Shaft | S.S 304 / S.S 410 |
| Specific Gravity | 1.004 (max.) |
| Versions | Single Angstrom phase 200-240V,50Hz,AC supply. CSCR,Three-phase 380-450 V,50V,AC supply. |
| Casing | Cast Iron / S.S 304 / (DIN 1.4509) |
| Coupling | S.S 304 / S.S 410 |
| Degree of Protection | IP 58 |
| Method of starting | CSCR |
| Outer Shell | Mild Steel/ S.S |
C.R.I. Openwell Submersible pumpsets are ideally suitable for open wells or tanks where a wide fluctuation of water level occur. This work under water and rest at the bottom of the well. Prime mover is rewindable, water-cooled motor
Motor sealing is made by polymers, ‘O’ rings, Oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel.
APPLICATIONSAdditional Information:
Product Details:
| Motor Speed (RPM) | 2900 RPM |
| Chlorine Ion Density | 500 ppm |
| Pump Shaft | S.S 304 / S.S 410 |
| Hardness | 300 ppm |
| Allowable Solid | 3000 ppm |
| Turbidity | 50 ppm silica scale |
| Versions | Single Angstrom phase 240V,50Hz,AC supply. CSCR,Three-phase 380-450 V,50V,AC supply. |
| Sand Guard Rubber | Nitrile Rubber |
| Maximum Liquid Temperature | 33 Angstrom degree C |
| Diaphragm | High Nitrile Rubber |
| Viscosity | 1.75 x 106 Angstrom m2/sec |
| Diffuser Chamber | Noryl |
| Casing | Cast Iron / S.S 304 / (DIN 1.4509) |
| Valve | Delrin |
| Stop Angstrom Ring | S.S 304 / Hylem |
| Outer Shell | Mild Steel/ S.S |
| Journal Bearings | LTB4 |
| Coupling | S.S 304 / S.S 410 |
| Intermediate Angstrom Bearing Angstrom | S.S 304 / NBR |
| Thurst Assembly | Leaded Bronze & Compostos / S.S 420 Vs Graphite Carbon |
| Impeller | Cast Iron / Noryl / Delrin / S.S 304 |
| Method of starting | CSCR |
| pH value | 6.5 to 8.5 |
| Specific Gravity | 1.004 (max.) |
| Degree of Protection | IP 58 |
| Upper Housing | Cast Iron |
| Type of Duty | S1(Continous) |
| Locking Strip | Mild Steel / S.S |
| Maximum Total Head | Upto 108 Metre |
| Shaft | SS 410 |
| Valve Seat | Nitrile butyl rubber |
| Direction of Rotation | Counterclockwise from driving End(Vertical OWS),Clockwise from driving end( Horizontal OWS) |
| Maximum Flow Rate | 10 lps(36 m^3(angstrom)/hr) |
| Power Range | 0.7 to 3 HP(.37kW-2.2kW) |
| Nominal Outlet Size | 25,32,40,50 & 65 mm |
C.R.I. Openwell Submersible pumpsets are ideally suitable for open wells or tanks where a wide fluctuation of water level occur. This work under water and rest at the bottom of the well. Prime mover is rewindable, water-cooled motor
Motor sealing is made by polymers, ‘O’ rings, Oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel.
APPLICATIONSAdditional Information:
Product Details:
| Shaft Seal | Nitrile butyl Rubber |
| Pump Shaft | S.S 304 / S.S 410 |
| Hardness | 300 ppm (max.) |
| Nominal Outlet Size | 25,32,40,50 & 65 mm |
| Diaphragm | High Nitrile Rubber |
| Chlorine Ion Density | 500 ppm (max.) |
| Viscosity | 1.75 x 10^6 Angstrom m^2/sec (max.) |
| Degree of Protection | IP 58 |
| Thrust Assembly | Leaded Bronze & Compostos / S.S 420 Vs Graphite Carbon |
| Journal Bearings | LTB4 |
| Sand Guard Rubber | Nitrile Rubber |
| Check Angstrom Valve Angstrom Housing | Cast Iron |
| Check Valve | Delrin |
| Stop Angstrom Ring | S.S 304 / Hylem |
| Permissiable Amount of Sand | 50 gm/m(Angstrom)^3 (max.) |
| Shaft | SS- 410 |
| Check Valve Seat | Nitrile butyl rubber |
| Method of starting | CSCR |
| Maximum Liquid Temperature | 33 Angstrom Degree Celsius (max.) |
| Specific Gravity | 1.004 (max.) |
| Versions | Single Angstrom phase 200-240V,50Hz,AC supply. CSCR,Three-phase 380-450 V,50V,AC supply. |
| Direction of Rotation | Counterclockwise from driving End(Vertical OWS),Clockwise from driving end( Horizontal OWS) |
| Type of Duty | S1(Continous) |
| Speed | 2880 RPM |
| Locking Strip | Mild Steel / S.S |
| Diffuser Chamber | Noryl |
| Turbidity | 50-ppm silica scale (max.) |
| Casing | Cast Iron / S.S 304 / (DIN 1.4509) |
| Allowable Solid | 3000 ppm (max.) |
| Maximum Total Head | Upto 108 Metre |
| Power Range | 0.7 to 3 HP(.37kW-2.2kW) |
| Impeller | Cast Iron / Noryl / Delrin / S.S 304 |
| Intermediate Angstrom Bearing Angstrom | S.S 304 / NBR |
| Maximum Flow Rate | 10 lps(36 m^3(angstrom)/hr) |
C.R.I. Openwell Submersible pumpsets are ideally suitable for open wells or tanks where a wide fluctuation of water level occur. This work under water and rest at the bottom of the well. Prime mover is rewindable, water-cooled motor
Product Details:
| Number Of Stages | Single-stage Pump |
| Motor Horsepower | 1 - 3 HP |
| Brand | CRI |
| Type | Horizontal |
| Motor Phase | Single Phase |
| Head | 15 to 50 m |
| Power Rating | 3 Phase |
| Max Flow Rate | 45 m3/hr |
C.R.I. Openwell Submersible pumpsets are ideally suitable for open wells or tanks where a wide fluctuation of water level occur. This work under water and rest at the bottom of the well. Prime mover is rewindable, water-cooled motor
Product Details:
| Number Of Stages | Single-stage Pump |
| Motor Horsepower | Less than 1 HP |
| Brand | CRI |
| Type | Water Filled |
| Motor Phase | Three Phase |
| Head | 15 to 50 m |
Application
Product Details:
| Motor Horsepower | 5 to 20 HP |
| Motor Phase | Three Phase |
| Power Source | Electric |
| Brand | CRI |
| Maximum Head | 15 to 50 m |
| Warranty | 12 months |
| Maximum Discharge Flow | 501-1000 LPM |
| Installation/After Sales Service | Yes |
| Usage/Application | Industrial, Domestic, Agriculture |
C.R.I. Openwell Submersible pumpsets are ideally suitable for open wells or tanks where a wide fluctuation of water level occur. This work under water and rest at the bottom of the well. Prime mover is rewindable, water-cooled motor
Motor sealing is made by polymers, ‘O’ rings, Oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel.
APPLICATIONSAdditional Information:
Product Details:
| Motor Horsepower | Less than 1 HP |
| Motor Phase/Stage | Single Phase |
| Number Of Stages | Single-stage Pump |
| Motor Power | 0.75 kw |
| Type | Electric |
| Discharge Outlet Size | 25x25 mm |
| Motor Phase | Single Phase |
| Head | 15 to 50 m |
| Brand | CRI |
| Power Source | Pump Only |
| Motor Speed | 2900 RPM |
| Pump Size | 25mm |
| Min Flow | 1800 LPH |
| Max Flow | 10800 LPH |
| Power | 0.75 kW |
C.R.I. Openwell Submersible pumpsets are ideally suitable for open wells or tanks where a wide fluctuation of water level occur. This work under water and rest at the bottom of the well. Prime mover is rewindable, water-cooled motor
Product Details:
| Motor Speed (RPM) | 2900 RPM |
| Flow Range | 194 m3/hr |
| Brand | CRI |
| Discharge Outlet Size | 54 Inch |
| Motor Horsepower | 3 HP |
| Motor Phase | Three Phase |
| Power Source | AC Powered |
| Motor Voltage | 415 V |
| Part Name | Material |
|---|---|
| Pump Casing | Cast Iron |
| Impeller | Cast Iron / SS 410 / Bronze |
| Bracket | Cast Iron |
| Motor Shaft | SS 410 |
Additional Information:
Product Details:
| Minimum Order Quantity | 5 Piece |
| Power | 3 HP |
| Power Source | Electric |
| Turbidity | 50-ppm silica scale (max.) |
| Nominal Delivery Size | 50,65,80 & 100 mm |
| Journal Bearing | LTB 4 |
| Maximum Total Head | Upto 341 metre |
| Maximum Start per Hour | 10 times |
| Viscosity | 1.75 x 10^6 Angstrom m^2/sec (max.) |
| Method of Starting | Direct on line upto 5.5kW,SD upto 37kW |
| pH Value | 6.5 to 8.5 |
| Shaft | SS AISI 410 / EN-8 |
| Pump Casing | Cast iron |
| Type of Duty | S1(continous) |
| Rear Cover | Cast Iron |
| Degree of Protection | IP 58 |
| Permissible amount of sand | 25 gm/m(Angstrom)^3 (max.) |
| Stator Shell | Cast iron / S.S / M.S |
| Direction of Rotation | Counter Clockwise from driving end |
| Shaft Seal | Nitrile butyl rubber |
| Maximum Flow Rate | Upto 195 m^3(Angstrom)/hr(54lps) |
| Versions | Three-phase,380-415V,50Hz,AC supply |
| Diaphragm | High Nitrile butyl rubber |
| Speed | 2900 RPM |
| Hardness | 300 ppm (max.) |
| Power Range | 2.2kW-15kW |
| Thurst Assembly | Leaded Bronze & Compostos / SS 420 with Graphite Carbon |
| Impeller | Cast iron / SS 410 / LTB-2 |
| Allowable Solid | 3000 ppm (max.) |
| Maximum Liquid Temperature | 33 Angstrom degree C (max.) |
| Specific Gravity | 1.004 (max.) |
| Chlorine Ion Density | 500 ppm (max.) |
C.R.I. Openwell Submersible pumpsets are ideally suitable for open wells or tanks where a wide fluctuation of water level occur. This work under water and rest at the bottom of the well. Prime mover is rewindable, water-cooled motor
Motor sealing is made by polymers, O rings, Oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operators manual. Three phase motor requires an adequate motor protection control panel.
APPLICATIONSAdditional Information:
Product Details:
| Minimum Order Quantity | 2 Piece |
| Power | 3 hp |
| Type | Horizontal |
| Motor Phase | Single Phase |
| Voltage | 220 v |
| Head | 33 m |
| Warranty | 12 months |
| Country of Origin | Made in India |
Additional Information:
Product Details:
| Number Of Stages | Single-stage Pump |
| Type | Horizontal |
| Motor Phase | Three Phase |
| Head | Less than 15 m |
| Motor Speed (RPM) | 2900 RPM |
| Brand | CRI |
| Motor Horsepower | 5 Hp |
| Color | Green |
| Type Of End Use | Agricultural |
C.R.I. Openwell Submersible pumpsets are ideally suitable for open wells or tanks where a wide fluctuation of water level occur. This work under water and rest at the bottom of the well. Prime mover is rewindable, water-cooled motor
Additional Information:
Product Details:
| Motor Horsepower | 1 to 3 HP |
| Motor Phase | Single Phase |
| Brand | CRI |
| Maximum Head | 15 to 50 m |
| Warranty | 12 months |
| Maximum Discharge Flow | 100 - 500 LPM |
| Material of Construction | SS |
| Installation/After Sales Service | No |
| Usage/Application | Industrial, Agriculture, Domestic, Resale Purpose |
Additional Information:
Product Details:
| Brand | CRI |
| Capacity | 1 hp |
| Material | Stainless Steel |
| Motor Phase | Three Phase |
| Motor Speed(RPM) | 2900 |
| Voltage(Volt) | 415 V |
| Shaft Seal | Nitrile butyl Rubber |
| Outer Shell | Mild Steel/ S.S |
| Intermediate Angstrom Bearing Angstrom | S.S 304 / NBR |
| Versions | Single Angstrom phase 200-240V,50Hz,AC supply. CSCR,Three-phase 380-450 V,50V,AC supply. |
| Turbidity | 50-ppm silica scale (max.) |
| Maximum Total Head | Upto 108 Metre |
| Nominal Outlet Size | 25,32,40,50 & 65 mm |
| Journal Bearings | LTB4 |
| Impeller | Cast Iron / Noryl / Delrin / S.S 304 |
| Pump Shaft | S.S 304 / S.S 410 |
| pH Value | 6.5 to 8.5 |
| Power Range | 0.7 to 3 HP(.37kW-2.2kW) |
| Method of starting | CSCR |
| Check Valve | Delrin |
| Diaphragm | High Nitrile Rubber |
| Casing | Cast Iron / S.S 304 / (DIN 1.4509) |
| Degree of Protection | IP 58 |
| Check Angstrom Valve Angstrom Housing | Cast Iron |
| Sand Guard Rubber | Nitrile Rubber |
| Maximum Liquid Temperature | 33 Angstrom Degree Celsius (max.) |
| Chlorine Ion Density | 500 ppm (max.) |
| Maximum Flow Rate | 10 lps(36 m^3(angstrom)/hr) |
| Speed | 2880 RPM |
| Locking Strip | Mild Steel / S.S |
| Diffuser Chamber | Noryl |
| Stop Angstrom Ring | S.S 304 / Hylem |
| Allowable Solid | 3000 ppm (max.) |
| Type of Duty | S1(Continous) |
| Shaft | SS- 410 |
| Thrust Assembly | Leaded Bronze & Compostos / S.S 420 Vs Graphite Carbon |
| Direction of Rotation | Counterclockwise from driving End(Vertical OWS),Clockwise from driving end( Horizontal OWS) |
| Viscosity | 1.75 x 10^6 Angstrom m^2/sec (max.) |
| Specific Gravity | 1.004 (max.) |
| Hardness | 300 ppm (max.) |
| Permissiable Amount of Sand | 50 gm/m(Angstrom)^3 (max.) |
Additional Information: